Hi, i want to flash OpenPli 2.1 on my ET9K, but after flashing it hangs in booting screen.
I disconnected all usb devices on my receiver and flash the new bootloader with ubifs support on it.
My internal HDD is a WD 2TB with ext3.
The status is the same, booting ....
What cause this issue? Any ideas?
13 replies to this topic
Re: Can´t flash OpenPli 2.1 #2
-
- PLi® Core member
- 32,766 posts
+245
Excellent
Posted 24 July 2011 - 11:16
did you update the bootloader?
There is a bootloader update to allow ubifs to be used (and we use ubifs in 2.1)
There is a bootloader update to allow ubifs to be used (and we use ubifs in 2.1)
Re: Can´t flash OpenPli 2.1 #3
-
- PLi® Core member
- 32,766 posts
+245
Excellent
Posted 24 July 2011 - 11:18
Re: Can´t flash OpenPli 2.1 #4
-
- PLi® Core member
- 56,288 posts
+691
Excellent
Posted 24 July 2011 - 11:18
He tels he did the bootloader stuf... but could this: http://www.pli-image...855#post_206855 also be the issue?
Re: Can´t flash OpenPli 2.1 #5
-
- PLi® Core member
- 32,766 posts
+245
Excellent
Posted 24 July 2011 - 11:18
He tels he did the bootloader stuf...
sorry, you're right, I overlooked that.
Re: Can´t flash OpenPli 2.1 #6
-
- Senior Member
- 52 posts
0
Neutral
Posted 24 July 2011 - 11:45
Here´s my Ouput as log:
https://rapidshare.c...e9k_bootlog.zip
I see some errors in flash, but it works with 2.0.
https://rapidshare.c...e9k_bootlog.zip
I see some errors in flash, but it works with 2.0.
Re: Can´t flash OpenPli 2.1 #7
-
- PLi® Core member
- 32,766 posts
+245
Excellent
Posted 24 July 2011 - 11:52
can't you just post the logs here?
(rapidshare is not really rapid, and when I extract the zipfile, I cannot open the logs)
(rapidshare is not really rapid, and when I extract the zipfile, I cannot open the logs)
Re: Can´t flash OpenPli 2.1 #8
-
- Senior Member
- 52 posts
0
Neutral
Posted 24 July 2011 - 12:02
Okay, here are the logs:
not working log 2.1:
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.07.24 12:22:53 =~=~=~=~=~=~=~=~=~=~=~=
BCM74130011
012
K1
K2
K3
K4
K5
Shmoo Version=3.8
DDR Freq=0x0000018C
%00000001%
RC1=00000005
WC1=00000001
RC2=0000001F
WC2=00000034
RC3=00000012
WC3=FFFFFFE8
RC4=00000012
WC4=00000033
NWC=0000000D
RC5=00000006
WC5=0000000D
RC6=0000001C
WC6=0000000D
NRC=00000011
RW=00000017
WW=0000004C
G=00000000 R=00000011 W=0000000D
BL=00000000
RC1=00000004
RC2=0000001E
BL=00000001
RC1=00000007
RC2=0000001A
BL=00000002
RC1=00000005
RC2=00000017
BL=00000003
RC1=00000006
RC2=00000016
BL=00000004
RC1=00000008
RC2=00000018
BL=00000005
RC1=00000007
RC2=0000001B
BL=00000006
RC1=00000003
RC2=00000018
BL=00000007
RC1=00000005
RC2=00000016
SCfC3
COPY CODE
COMPARE CODE
4567
BCM97413B1 CFE v2.26, CFE core v2.12, Endian Mode: Little
Build Date: Mon Jul 18 21:03:30 WEDT 2011 (Administrator@buildserver)
Copyright © Broadcom Corporation.
start cfe init device
sec-0 nblks=8 blksiz=8192
sec-1 nblks=63 blksiz=65536
Enabling NAND flash at CS1, NOR flash at CS0
NAND Flash size = 128MB
CPU speed: 405MHz
Memory Config: 64-bit UMA
Device Tech: 1Gb
Total memory: 512MB
Boot Device: NOR
Total flash: 4MB
Initializing USB.
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub
CFE initialized.
Set default GPIO...
USB: New device connected to bus 1 hub 1 port 1[J
USB: Resetting device on bus 1 port 1[J
USB: Locating Class 09 Vendor 1A40 Product 0101: USB Hub
USB: New device connected to bus 1 hub 2 port 1[J
USB: Resetting device on bus 1 port 1[J
USB: Locating Class 08 Vendor 0EA0 Product 2168: Mass-Storage Device
USBMASS: Unit 0 connected[J
USB: New device connected to bus 1 hub 2 port 2[J
USB: Resetting device on bus 1 port 2[J
USB: Locating Class 02 Vendor DEAD Product BEEF: Ethernet Device
USB: [Transfer error: 4]
USB CDC Device (00:00:00:00:00:00)
found image:
openpli-2.1-20110723
flashing...
Reading usbdisk0:et9000/kernel.bin: Done. 3384921 bytes read
Programming...
offset=0 copysize=3384921
done. 3384921 bytes written
flashing...
Reading usbdisk0:et9000/rootfs.bin: Done. 49545216 bytes read
offset: 00000000 size: 07A00000
Force erasing...
Erasing flash...Erase address 0x2e00000 failed, bad block?
Programming...
offset=0 copysize=49545216
done. 49545216 bytes written
flashing completed!
booting...
Starting splash screen.
***************************************************
Found splash image - Width = 720 Height = 576
bmp ptr : 0x8fa00000 , surface ptr : 0xafc00000
***************************************************
Loader:elf Filesys:raw Dev:nandflash0.kernel File: Options:(null)
Loading: 0x80001000/6497856 0x80633640/142432 Entry address is 0x80005470
TP1 Entry Address at 0x80000ffc = 80005470
Starting program at 0x80005470
Linux version 2.6.31-3.2 (build@buildserver) (gcc version 4.4.4 (GCC) ) #1 SMP Sat Jul 23 05:14:44 CEST 2011
Fetching vars from bootloader... found 10 vars.
Early serial console at MMIO 0x10400b00 (options '115200n8')
console [uart0] enabled
Options: sata=1 enet=1 emac_1=1 no_mdio=0 docsis=0 pci=1 smp=1 moca=0 usb=1
Using 512 MB + 0 MB RAM (from CFE)
CPU revision is: 0002a044 (Brcm4380)
FPU revision is: 00130001
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
memory: 10000000 @ 20000000 (usable)
bmem: adding 192 MB RESERVED region at 64 MB (0x0c000000@0x04000000)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00030000
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000000 -> 0x00010000
0: 0x00020000 -> 0x00030000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129536
Kernel command line: bmem=192M lpj=203264 ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs rw console=null
PID hash table entries: 2048 (order: 11, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
Memory: 316292k/524288k available (5032k kernel code, 207644k reserved, 1102k data, 212k init, 0k highmem)
NR_IRQS:128
Detected MIPS clock frequency: 404 MHz (202.497 MHz counter)
Console: colour dummy device 80x25
Calibrating delay loop (skipped) preset value.. 406.52 BogoMIPS (lpj=203264)
Mount-cache hash table entries: 512
SMP: Booting CPU1...
CPU revision is: 0002a044 (Brcm4380)
FPU revision is: 00130001
Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
Calibrating delay loop (skipped) preset value.. 406.52 BogoMIPS (lpj=203264)
SMP: CPU1 is running
Brought up 2 CPUs
NET: Registered protocol family 16
PCI2.3->SDRAM window: 512 MB
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42)
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
NTFS driver 2.1.29 [Flags: R/W].
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 618
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A
loop: module loaded
brcm-pm: enabling sata clocks
PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
scsi0 : sata_brcmstb
scsi1 : sata_brcmstb
ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42
ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42
bcmemac: Broadcom STB 10/100 EMAC driver v3.0
bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:16:b4:03:75:70)
bcmemac: not registering interface #1 at 0x10090000 (no PHY detected)
pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new interface driver pegasus
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver net1080
usbcore: registered new interface driver cdc_subset
usbcore: registered new interface driver zaurus
Broadcom STB NAND controller (BrcmNand Controller)
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
brcm-pm: enabling usb clocks
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ehci-brcm ehci-brcm.1: Broadcom STB EHCI
ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3
ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci-brcm ohci-brcm.1: Broadcom STB OHCI
ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4
ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-8: SAMSUNG HD204UI, 1AQ10001, max UDMA/133
ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD204UI 1AQ1 PQ: 0 ANSI: 5
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
Bluetooth: Generic Bluetooth USB driver ver 0.5
usbcore: registered new interface driver btusb
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.20.
ALSA device list:
No soundcards found.
TCP cubic registered
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
NET: Registered protocol family 17
Bluetooth: L2CAP ver 2.13
Bluetooth: L2CAP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
EBI CS1: setting up NAND flash (primary)
mtd->oobsize=0, mtd->eccOobSize=0
NAND_CS_NAND_XOR=00000000
B4: NandSelect=50000200, nandConfig=15142200, chipSelect=1
brcmnand_read_id: CS1: dev_id=ecf10095
After: NandSelect=50000200, nandConfig=15142200
Block size=00020000, erase shift=17
NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
timing1 not adjusted: 5363444f
timing2 not adjusted: 00000fc6
eccLevel=15, 1Ksector=0, oob=16
nbrBitsPerCell=2, cellinfo=0, chip->cellinfo=00000000
<--brcmnand_set_acccontrol: acc b4: d7ff1010, after: d7ff1010
BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB on CS1
Found NAND on CS1: ACC=d7ff1010, cfg=15142200, flashId=ecf10095, tim1=5363444f, tim2=00000fc6
BrcmNAND version = 0x0302 128MB @00000000
B4: NandSelect=50000200, nandConfig=15142200, chipSelect=1
brcmnand_read_id: CS1: dev_id=ecf10095
After: NandSelect=50000200, nandConfig=15142200
Found NAND flash on Chip Select 1, chipSize=128MB, usable size=128MB, base=0
brcmnand_scan: B4 nand_select = 50000200
usb 2-1: new high speed USB device using ehci-brcm and address 2
brcmnand_scan: After nand_select = 50000200
page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
Brcm NAND controller version = 3.2 NAND flash size 128MB @18000000
ECC layout=brcmnand_oob_bch4_4k
brcmnand_scan: mtd->oobsize=64
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
-->brcmnand_default_bbt
brcmnand_default_bbt: bbt_td = bbt_main_descr
Bad block table Bbt0 not found for chip on CS1
Bad block table 1tbB not found for chip on CS1
Scanning device for bad blocks, options=00004000
ata2: SATA link down (SStatus 4 SControl 300)
Bad eraseblock 368 at 0x02e00000
-->brcmnand_isbad_raw(offs=7fe0000
-->brcmnand_isbad_raw(offs=7fc0000
sda:
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Creating 5 MTD partitions on "brcmnand.0":
0x000000000000-0x000007f00000 : "complete"
0x000000000000-0x000000400000 : "kernel"
0x000000400000-0x000000600000 : "boot"
0x000000600000-0x000007f00000 : "rootfs"
0x000007f00000-0x000008000000 : "bbt"
turn off boot console uart0
Working log 2.0:
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.07.24 12:30:36 =~=~=~=~=~=~=~=~=~=~=~=
BCM74130011
012
K1
K2
K3
K4
K5
Shmoo Version=3.8
DDR Freq=0x0000018C
%00000001%
RC1=00000005
WC1=FFFFFFE9
RC2=0000001F
WC2=00000031
RC3=00000012
WC3=FFFFFFE8
RC4=00000012
WC4=00000033
NWC=0000000D
RC5=00000006
WC5=0000000D
RC6=0000001F
WC6=0000000D
NRC=00000012
RW=0000001A
WW=0000004C
G=00000000 R=00000012 W=0000000D
BL=00000000
RC1=00000004
RC2=0000001F
BL=00000001
RC1=00000007
RC2=0000001A
BL=00000002
RC1=00000005
RC2=00000018
BL=00000003
RC1=00000006
RC2=00000016
BL=00000004
RC1=00000008
RC2=00000018
BL=00000005
RC1=00000007
RC2=0000001B
BL=00000006
RC1=00000003
RC2=00000019
BL=00000007
RC1=00000005
RC2=00000017
SCfC3
COPY CODE
COMPARE CODE
4567
BCM97413B1 CFE v2.26, CFE core v2.12, Endian Mode: Little
Build Date: Mon Jul 18 21:03:30 WEDT 2011 (Administrator@buildserver)
Copyright © Broadcom Corporation.
start cfe init device
sec-0 nblks=8 blksiz=8192
sec-1 nblks=63 blksiz=65536
Enabling NAND flash at CS1, NOR flash at CS0
NAND Flash size = 128MB
CPU speed: 405MHz
Memory Config: 64-bit UMA
Device Tech: 1Gb
Total memory: 512MB
Boot Device: NOR
Total flash: 4MB
Initializing USB.
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub
CFE initialized.
Set default GPIO...
USB: New device connected to bus 1 hub 1 port 1[J
USB: Resetting device on bus 1 port 1[J
USB: Locating Class 09 Vendor 1A40 Product 0101: USB Hub
USB: New device connected to bus 1 hub 2 port 1[J
USB: Resetting device on bus 1 port 1[J
USB: Locating Class 08 Vendor 090C Product 1000: Mass-Storage Device
USBMASS: Unit 0 connected[J
USB: New device connected to bus 1 hub 2 port 2[J
USB: Resetting device on bus 1 port 2[J
USB: Locating Class 02 Vendor DEAD Product BEEF: Ethernet Device
USB: [Transfer error: 4]
USB CDC Device (00:00:00:00:00:00)
found image:
et9000-20110724
flash image? (OK/CANCEL)
flashing...
Reading usbdisk0:et9000/kernel.bin: Done. 4194304 bytes read
Programming...
offset=0 copysize=4194304
done. 4194304 bytes written
flashing...
Reading usbdisk0:et9000/boot.bin: Done. 456 bytes read
offset: 00000000 size: 00200000
Force erasing...
Erasing flash...Programming...
offset=0 copysize=456
done. 456 bytes written
flashing...
Reading usbdisk0:et9000/rootfs.bin: Done. 53021732 bytes read
offset: 00000000 size: 07A00000
Force erasing...
Erasing flash...Erase address 0x2e00000 failed, bad block?
Programming...
offset=0 copysize=53021732
done. 53021732 bytes written
flashing completed!
booting...
Starting splash screen.
***************************************************
Found splash image - Width = 720 Height = 576
bmp ptr : 0x8fa00000 , surface ptr : 0xafc00000
***************************************************
Loader:elf Filesys:raw Dev:nandflash0.kernel File: Options:(null)
Loading: !!!!! UNC read error occurred, while reading from NAND flash -1
0x80001000/6497856 0x80633640/142432 Entry address is 0x80005470
TP1 Entry Address at 0x80000ffc = 80005470
Starting program at 0x80005470
Linux version 2.6.31-3.2 (build@buildserver) (gcc version 4.4.4 (GCC) ) #1 SMP Tue Jul 19 05:02:58 CEST 2011
Fetching vars from bootloader... found 10 vars.
Early serial console at MMIO 0x10400b00 (options '115200n8')
console [uart0] enabled
Options: sata=1 enet=1 emac_1=1 no_mdio=0 docsis=0 pci=1 smp=1 moca=0 usb=1
Using 512 MB + 0 MB RAM (from CFE)
CPU revision is: 0002a044 (Brcm4380)
FPU revision is: 00130001
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
memory: 10000000 @ 20000000 (usable)
bmem: adding 192 MB RESERVED region at 64 MB (0x0c000000@0x04000000)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00030000
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000000 -> 0x00010000
0: 0x00020000 -> 0x00030000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129536
Kernel command line: bmem=192M lpj=203264 root=/dev/mtdblock3 rootfstype=jffs2 rw console=null
PID hash table entries: 2048 (order: 11, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
Memory: 316292k/524288k available (5032k kernel code, 207644k reserved, 1102k data, 212k init, 0k highmem)
NR_IRQS:128
Detected MIPS clock frequency: 405 MHz (202.500 MHz counter)
Console: colour dummy device 80x25
Calibrating delay loop (skipped) preset value.. 406.52 BogoMIPS (lpj=203264)
Mount-cache hash table entries: 512
SMP: Booting CPU1...
CPU revision is: 0002a044 (Brcm4380)
FPU revision is: 00130001
Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
Calibrating delay loop (skipped) preset value.. 406.52 BogoMIPS (lpj=203264)
SMP: CPU1 is running
Brought up 2 CPUs
NET: Registered protocol family 16
PCI2.3->SDRAM window: 512 MB
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42)
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
NTFS driver 2.1.29 [Flags: R/W].
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 618
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A
loop: module loaded
brcm-pm: enabling sata clocks
PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
scsi0 : sata_brcmstb
scsi1 : sata_brcmstb
ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42
ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42
bcmemac: Broadcom STB 10/100 EMAC driver v3.0
bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:16:b4:03:75:70)
bcmemac: not registering interface #1 at 0x10090000 (no PHY detected)
pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new interface driver pegasus
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver net1080
usbcore: registered new interface driver cdc_subset
usbcore: registered new interface driver zaurus
Broadcom STB NAND controller (BrcmNand Controller)
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
brcm-pm: enabling usb clocks
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ehci-brcm ehci-brcm.1: Broadcom STB EHCI
ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3
ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci-brcm ohci-brcm.1: Broadcom STB OHCI
ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4
ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-8: SAMSUNG HD204UI, 1AQ10001, max UDMA/133
ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD204UI 1AQ1 PQ: 0 ANSI: 5
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
Bluetooth: Generic Bluetooth USB driver ver 0.5
usbcore: registered new interface driver btusb
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.20.
ALSA device list:
No soundcards found.
TCP cubic registered
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
NET: Registered protocol family 17
Bluetooth: L2CAP ver 2.13
Bluetooth: L2CAP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
EBI CS1: setting up NAND flash (primary)
mtd->oobsize=0, mtd->eccOobSize=0
NAND_CS_NAND_XOR=00000000
B4: NandSelect=50000200, nandConfig=15142200, chipSelect=1
brcmnand_read_id: CS1: dev_id=ecf10095
After: NandSelect=50000200, nandConfig=15142200
Block size=00020000, erase shift=17
NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
timing1 not adjusted: 5363444f
timing2 not adjusted: 00000fc6
eccLevel=15, 1Ksector=0, oob=16
nbrBitsPerCell=2, cellinfo=0, chip->cellinfo=00000000
<--brcmnand_set_acccontrol: acc b4: d7ff1010, after: d7ff1010
BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB on CS1
Found NAND on CS1: ACC=d7ff1010, cfg=15142200, flashId=ecf10095, tim1=5363444f, tim2=00000fc6
BrcmNAND version = 0x0302 128MB @00000000
B4: NandSelect=50000200, nandConfig=15142200, chipSelect=1
brcmnand_read_id: CS1: dev_id=ecf10095
After: NandSelect=50000200, nandConfig=15142200
Found NAND flash on Chip Select 1, chipSize=128MB, usable size=128MB, base=0
brcmnand_scan: B4 nand_select = 50000200
usb 2-1: new high speed USB device using ehci-brcm and address 2
brcmnand_scan: After nand_select = 50000200
page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
Brcm NAND controller version = 3.2 NAND flash size 128MB @18000000
ECC layout=brcmnand_oob_bch4_4k
brcmnand_scan: mtd->oobsize=64
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
-->brcmnand_default_bbt
brcmnand_default_bbt: bbt_td = bbt_main_descr
Bad block table Bbt0 not found for chip on CS1
Bad block table 1tbB not found for chip on CS1
Scanning device for bad blocks, options=00004000
ata2: SATA link down (SStatus 4 SControl 300)
Bad eraseblock 368 at 0x02e00000
-->brcmnand_isbad_raw(offs=7fe0000
-->brcmnand_isbad_raw(offs=7fc0000
sda:
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Creating 5 MTD partitions on "brcmnand.0":
0x000000000000-0x000007f00000 : "complete"
0x000000000000-0x000000400000 : "kernel"
0x000000400000-0x000000600000 : "boot"
0x000000600000-0x000007f00000 : "rootfs"
0x000007f00000-0x000008000000 : "bbt"
turn off boot console uart0
not working log 2.1:
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.07.24 12:22:53 =~=~=~=~=~=~=~=~=~=~=~=
BCM74130011
012
K1
K2
K3
K4
K5
Shmoo Version=3.8
DDR Freq=0x0000018C
%00000001%
RC1=00000005
WC1=00000001
RC2=0000001F
WC2=00000034
RC3=00000012
WC3=FFFFFFE8
RC4=00000012
WC4=00000033
NWC=0000000D
RC5=00000006
WC5=0000000D
RC6=0000001C
WC6=0000000D
NRC=00000011
RW=00000017
WW=0000004C
G=00000000 R=00000011 W=0000000D
BL=00000000
RC1=00000004
RC2=0000001E
BL=00000001
RC1=00000007
RC2=0000001A
BL=00000002
RC1=00000005
RC2=00000017
BL=00000003
RC1=00000006
RC2=00000016
BL=00000004
RC1=00000008
RC2=00000018
BL=00000005
RC1=00000007
RC2=0000001B
BL=00000006
RC1=00000003
RC2=00000018
BL=00000007
RC1=00000005
RC2=00000016
SCfC3
COPY CODE
COMPARE CODE
4567
BCM97413B1 CFE v2.26, CFE core v2.12, Endian Mode: Little
Build Date: Mon Jul 18 21:03:30 WEDT 2011 (Administrator@buildserver)
Copyright © Broadcom Corporation.
start cfe init device
sec-0 nblks=8 blksiz=8192
sec-1 nblks=63 blksiz=65536
Enabling NAND flash at CS1, NOR flash at CS0
NAND Flash size = 128MB
CPU speed: 405MHz
Memory Config: 64-bit UMA
Device Tech: 1Gb
Total memory: 512MB
Boot Device: NOR
Total flash: 4MB
Initializing USB.
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub
CFE initialized.
Set default GPIO...
USB: New device connected to bus 1 hub 1 port 1[J
USB: Resetting device on bus 1 port 1[J
USB: Locating Class 09 Vendor 1A40 Product 0101: USB Hub
USB: New device connected to bus 1 hub 2 port 1[J
USB: Resetting device on bus 1 port 1[J
USB: Locating Class 08 Vendor 0EA0 Product 2168: Mass-Storage Device
USBMASS: Unit 0 connected[J
USB: New device connected to bus 1 hub 2 port 2[J
USB: Resetting device on bus 1 port 2[J
USB: Locating Class 02 Vendor DEAD Product BEEF: Ethernet Device
USB: [Transfer error: 4]
USB CDC Device (00:00:00:00:00:00)
found image:
openpli-2.1-20110723
flashing...
Reading usbdisk0:et9000/kernel.bin: Done. 3384921 bytes read
Programming...
offset=0 copysize=3384921
done. 3384921 bytes written
flashing...
Reading usbdisk0:et9000/rootfs.bin: Done. 49545216 bytes read
offset: 00000000 size: 07A00000
Force erasing...
Erasing flash...Erase address 0x2e00000 failed, bad block?
Programming...
offset=0 copysize=49545216
done. 49545216 bytes written
flashing completed!
booting...
Starting splash screen.
***************************************************
Found splash image - Width = 720 Height = 576
bmp ptr : 0x8fa00000 , surface ptr : 0xafc00000
***************************************************
Loader:elf Filesys:raw Dev:nandflash0.kernel File: Options:(null)
Loading: 0x80001000/6497856 0x80633640/142432 Entry address is 0x80005470
TP1 Entry Address at 0x80000ffc = 80005470
Starting program at 0x80005470
Linux version 2.6.31-3.2 (build@buildserver) (gcc version 4.4.4 (GCC) ) #1 SMP Sat Jul 23 05:14:44 CEST 2011
Fetching vars from bootloader... found 10 vars.
Early serial console at MMIO 0x10400b00 (options '115200n8')
console [uart0] enabled
Options: sata=1 enet=1 emac_1=1 no_mdio=0 docsis=0 pci=1 smp=1 moca=0 usb=1
Using 512 MB + 0 MB RAM (from CFE)
CPU revision is: 0002a044 (Brcm4380)
FPU revision is: 00130001
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
memory: 10000000 @ 20000000 (usable)
bmem: adding 192 MB RESERVED region at 64 MB (0x0c000000@0x04000000)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00030000
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000000 -> 0x00010000
0: 0x00020000 -> 0x00030000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129536
Kernel command line: bmem=192M lpj=203264 ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs rw console=null
PID hash table entries: 2048 (order: 11, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
Memory: 316292k/524288k available (5032k kernel code, 207644k reserved, 1102k data, 212k init, 0k highmem)
NR_IRQS:128
Detected MIPS clock frequency: 404 MHz (202.497 MHz counter)
Console: colour dummy device 80x25
Calibrating delay loop (skipped) preset value.. 406.52 BogoMIPS (lpj=203264)
Mount-cache hash table entries: 512
SMP: Booting CPU1...
CPU revision is: 0002a044 (Brcm4380)
FPU revision is: 00130001
Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
Calibrating delay loop (skipped) preset value.. 406.52 BogoMIPS (lpj=203264)
SMP: CPU1 is running
Brought up 2 CPUs
NET: Registered protocol family 16
PCI2.3->SDRAM window: 512 MB
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42)
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
NTFS driver 2.1.29 [Flags: R/W].
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 618
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A
loop: module loaded
brcm-pm: enabling sata clocks
PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
scsi0 : sata_brcmstb
scsi1 : sata_brcmstb
ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42
ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42
bcmemac: Broadcom STB 10/100 EMAC driver v3.0
bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:16:b4:03:75:70)
bcmemac: not registering interface #1 at 0x10090000 (no PHY detected)
pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new interface driver pegasus
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver net1080
usbcore: registered new interface driver cdc_subset
usbcore: registered new interface driver zaurus
Broadcom STB NAND controller (BrcmNand Controller)
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
brcm-pm: enabling usb clocks
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ehci-brcm ehci-brcm.1: Broadcom STB EHCI
ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3
ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci-brcm ohci-brcm.1: Broadcom STB OHCI
ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4
ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-8: SAMSUNG HD204UI, 1AQ10001, max UDMA/133
ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD204UI 1AQ1 PQ: 0 ANSI: 5
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
Bluetooth: Generic Bluetooth USB driver ver 0.5
usbcore: registered new interface driver btusb
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.20.
ALSA device list:
No soundcards found.
TCP cubic registered
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
NET: Registered protocol family 17
Bluetooth: L2CAP ver 2.13
Bluetooth: L2CAP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
EBI CS1: setting up NAND flash (primary)
mtd->oobsize=0, mtd->eccOobSize=0
NAND_CS_NAND_XOR=00000000
B4: NandSelect=50000200, nandConfig=15142200, chipSelect=1
brcmnand_read_id: CS1: dev_id=ecf10095
After: NandSelect=50000200, nandConfig=15142200
Block size=00020000, erase shift=17
NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
timing1 not adjusted: 5363444f
timing2 not adjusted: 00000fc6
eccLevel=15, 1Ksector=0, oob=16
nbrBitsPerCell=2, cellinfo=0, chip->cellinfo=00000000
<--brcmnand_set_acccontrol: acc b4: d7ff1010, after: d7ff1010
BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB on CS1
Found NAND on CS1: ACC=d7ff1010, cfg=15142200, flashId=ecf10095, tim1=5363444f, tim2=00000fc6
BrcmNAND version = 0x0302 128MB @00000000
B4: NandSelect=50000200, nandConfig=15142200, chipSelect=1
brcmnand_read_id: CS1: dev_id=ecf10095
After: NandSelect=50000200, nandConfig=15142200
Found NAND flash on Chip Select 1, chipSize=128MB, usable size=128MB, base=0
brcmnand_scan: B4 nand_select = 50000200
usb 2-1: new high speed USB device using ehci-brcm and address 2
brcmnand_scan: After nand_select = 50000200
page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
Brcm NAND controller version = 3.2 NAND flash size 128MB @18000000
ECC layout=brcmnand_oob_bch4_4k
brcmnand_scan: mtd->oobsize=64
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
-->brcmnand_default_bbt
brcmnand_default_bbt: bbt_td = bbt_main_descr
Bad block table Bbt0 not found for chip on CS1
Bad block table 1tbB not found for chip on CS1
Scanning device for bad blocks, options=00004000
ata2: SATA link down (SStatus 4 SControl 300)
Bad eraseblock 368 at 0x02e00000
-->brcmnand_isbad_raw(offs=7fe0000
-->brcmnand_isbad_raw(offs=7fc0000
sda:
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Creating 5 MTD partitions on "brcmnand.0":
0x000000000000-0x000007f00000 : "complete"
0x000000000000-0x000000400000 : "kernel"
0x000000400000-0x000000600000 : "boot"
0x000000600000-0x000007f00000 : "rootfs"
0x000007f00000-0x000008000000 : "bbt"
turn off boot console uart0
Working log 2.0:
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.07.24 12:30:36 =~=~=~=~=~=~=~=~=~=~=~=
BCM74130011
012
K1
K2
K3
K4
K5
Shmoo Version=3.8
DDR Freq=0x0000018C
%00000001%
RC1=00000005
WC1=FFFFFFE9
RC2=0000001F
WC2=00000031
RC3=00000012
WC3=FFFFFFE8
RC4=00000012
WC4=00000033
NWC=0000000D
RC5=00000006
WC5=0000000D
RC6=0000001F
WC6=0000000D
NRC=00000012
RW=0000001A
WW=0000004C
G=00000000 R=00000012 W=0000000D
BL=00000000
RC1=00000004
RC2=0000001F
BL=00000001
RC1=00000007
RC2=0000001A
BL=00000002
RC1=00000005
RC2=00000018
BL=00000003
RC1=00000006
RC2=00000016
BL=00000004
RC1=00000008
RC2=00000018
BL=00000005
RC1=00000007
RC2=0000001B
BL=00000006
RC1=00000003
RC2=00000019
BL=00000007
RC1=00000005
RC2=00000017
SCfC3
COPY CODE
COMPARE CODE
4567
BCM97413B1 CFE v2.26, CFE core v2.12, Endian Mode: Little
Build Date: Mon Jul 18 21:03:30 WEDT 2011 (Administrator@buildserver)
Copyright © Broadcom Corporation.
start cfe init device
sec-0 nblks=8 blksiz=8192
sec-1 nblks=63 blksiz=65536
Enabling NAND flash at CS1, NOR flash at CS0
NAND Flash size = 128MB
CPU speed: 405MHz
Memory Config: 64-bit UMA
Device Tech: 1Gb
Total memory: 512MB
Boot Device: NOR
Total flash: 4MB
Initializing USB.
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub
CFE initialized.
Set default GPIO...
USB: New device connected to bus 1 hub 1 port 1[J
USB: Resetting device on bus 1 port 1[J
USB: Locating Class 09 Vendor 1A40 Product 0101: USB Hub
USB: New device connected to bus 1 hub 2 port 1[J
USB: Resetting device on bus 1 port 1[J
USB: Locating Class 08 Vendor 090C Product 1000: Mass-Storage Device
USBMASS: Unit 0 connected[J
USB: New device connected to bus 1 hub 2 port 2[J
USB: Resetting device on bus 1 port 2[J
USB: Locating Class 02 Vendor DEAD Product BEEF: Ethernet Device
USB: [Transfer error: 4]
USB CDC Device (00:00:00:00:00:00)
found image:
et9000-20110724
flash image? (OK/CANCEL)
flashing...
Reading usbdisk0:et9000/kernel.bin: Done. 4194304 bytes read
Programming...
offset=0 copysize=4194304
done. 4194304 bytes written
flashing...
Reading usbdisk0:et9000/boot.bin: Done. 456 bytes read
offset: 00000000 size: 00200000
Force erasing...
Erasing flash...Programming...
offset=0 copysize=456
done. 456 bytes written
flashing...
Reading usbdisk0:et9000/rootfs.bin: Done. 53021732 bytes read
offset: 00000000 size: 07A00000
Force erasing...
Erasing flash...Erase address 0x2e00000 failed, bad block?
Programming...
offset=0 copysize=53021732
done. 53021732 bytes written
flashing completed!
booting...
Starting splash screen.
***************************************************
Found splash image - Width = 720 Height = 576
bmp ptr : 0x8fa00000 , surface ptr : 0xafc00000
***************************************************
Loader:elf Filesys:raw Dev:nandflash0.kernel File: Options:(null)
Loading: !!!!! UNC read error occurred, while reading from NAND flash -1
0x80001000/6497856 0x80633640/142432 Entry address is 0x80005470
TP1 Entry Address at 0x80000ffc = 80005470
Starting program at 0x80005470
Linux version 2.6.31-3.2 (build@buildserver) (gcc version 4.4.4 (GCC) ) #1 SMP Tue Jul 19 05:02:58 CEST 2011
Fetching vars from bootloader... found 10 vars.
Early serial console at MMIO 0x10400b00 (options '115200n8')
console [uart0] enabled
Options: sata=1 enet=1 emac_1=1 no_mdio=0 docsis=0 pci=1 smp=1 moca=0 usb=1
Using 512 MB + 0 MB RAM (from CFE)
CPU revision is: 0002a044 (Brcm4380)
FPU revision is: 00130001
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
memory: 10000000 @ 20000000 (usable)
bmem: adding 192 MB RESERVED region at 64 MB (0x0c000000@0x04000000)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00030000
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000000 -> 0x00010000
0: 0x00020000 -> 0x00030000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129536
Kernel command line: bmem=192M lpj=203264 root=/dev/mtdblock3 rootfstype=jffs2 rw console=null
PID hash table entries: 2048 (order: 11, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
Memory: 316292k/524288k available (5032k kernel code, 207644k reserved, 1102k data, 212k init, 0k highmem)
NR_IRQS:128
Detected MIPS clock frequency: 405 MHz (202.500 MHz counter)
Console: colour dummy device 80x25
Calibrating delay loop (skipped) preset value.. 406.52 BogoMIPS (lpj=203264)
Mount-cache hash table entries: 512
SMP: Booting CPU1...
CPU revision is: 0002a044 (Brcm4380)
FPU revision is: 00130001
Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
Calibrating delay loop (skipped) preset value.. 406.52 BogoMIPS (lpj=203264)
SMP: CPU1 is running
Brought up 2 CPUs
NET: Registered protocol family 16
PCI2.3->SDRAM window: 512 MB
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42)
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
NTFS driver 2.1.29 [Flags: R/W].
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 618
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A
loop: module loaded
brcm-pm: enabling sata clocks
PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
scsi0 : sata_brcmstb
scsi1 : sata_brcmstb
ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42
ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42
bcmemac: Broadcom STB 10/100 EMAC driver v3.0
bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:16:b4:03:75:70)
bcmemac: not registering interface #1 at 0x10090000 (no PHY detected)
pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new interface driver pegasus
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver net1080
usbcore: registered new interface driver cdc_subset
usbcore: registered new interface driver zaurus
Broadcom STB NAND controller (BrcmNand Controller)
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
brcm-pm: enabling usb clocks
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ehci-brcm ehci-brcm.1: Broadcom STB EHCI
ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3
ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci-brcm ohci-brcm.1: Broadcom STB OHCI
ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4
ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-8: SAMSUNG HD204UI, 1AQ10001, max UDMA/133
ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD204UI 1AQ1 PQ: 0 ANSI: 5
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
Bluetooth: Generic Bluetooth USB driver ver 0.5
usbcore: registered new interface driver btusb
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.20.
ALSA device list:
No soundcards found.
TCP cubic registered
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
NET: Registered protocol family 17
Bluetooth: L2CAP ver 2.13
Bluetooth: L2CAP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
EBI CS1: setting up NAND flash (primary)
mtd->oobsize=0, mtd->eccOobSize=0
NAND_CS_NAND_XOR=00000000
B4: NandSelect=50000200, nandConfig=15142200, chipSelect=1
brcmnand_read_id: CS1: dev_id=ecf10095
After: NandSelect=50000200, nandConfig=15142200
Block size=00020000, erase shift=17
NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
timing1 not adjusted: 5363444f
timing2 not adjusted: 00000fc6
eccLevel=15, 1Ksector=0, oob=16
nbrBitsPerCell=2, cellinfo=0, chip->cellinfo=00000000
<--brcmnand_set_acccontrol: acc b4: d7ff1010, after: d7ff1010
BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB on CS1
Found NAND on CS1: ACC=d7ff1010, cfg=15142200, flashId=ecf10095, tim1=5363444f, tim2=00000fc6
BrcmNAND version = 0x0302 128MB @00000000
B4: NandSelect=50000200, nandConfig=15142200, chipSelect=1
brcmnand_read_id: CS1: dev_id=ecf10095
After: NandSelect=50000200, nandConfig=15142200
Found NAND flash on Chip Select 1, chipSize=128MB, usable size=128MB, base=0
brcmnand_scan: B4 nand_select = 50000200
usb 2-1: new high speed USB device using ehci-brcm and address 2
brcmnand_scan: After nand_select = 50000200
page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
Brcm NAND controller version = 3.2 NAND flash size 128MB @18000000
ECC layout=brcmnand_oob_bch4_4k
brcmnand_scan: mtd->oobsize=64
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
-->brcmnand_default_bbt
brcmnand_default_bbt: bbt_td = bbt_main_descr
Bad block table Bbt0 not found for chip on CS1
Bad block table 1tbB not found for chip on CS1
Scanning device for bad blocks, options=00004000
ata2: SATA link down (SStatus 4 SControl 300)
Bad eraseblock 368 at 0x02e00000
-->brcmnand_isbad_raw(offs=7fe0000
-->brcmnand_isbad_raw(offs=7fc0000
sda:
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Creating 5 MTD partitions on "brcmnand.0":
0x000000000000-0x000007f00000 : "complete"
0x000000000000-0x000000400000 : "kernel"
0x000000400000-0x000000600000 : "boot"
0x000000600000-0x000007f00000 : "rootfs"
0x000007f00000-0x000008000000 : "bbt"
turn off boot console uart0
Re: Can´t flash OpenPli 2.1 #9
-
- Senior Member
- 52 posts
0
Neutral
Posted 24 July 2011 - 18:42
here´s the enhanced log after update 2.1
CFE initialized.
Set default GPIO...
USB: New device connected to bus 1 hub 1 port 1
USB: Resetting device on bus 1 port 1
USB: Locating Class 09 Vendor 1A40 Product 0101: USB Hub
USB: New device connected to bus 1 hub 2 port 2
USB: Resetting device on bus 1 port 2
USB: Locating Class 02 Vendor DEAD Product BEEF: Ethernet Device
USB: [Transfer error: 4]
USB CDC Device (00:00:00:00:00:00)
Starting splash screen.
***************************************************
Found splash image - Width = 720 Height = 576
bmp ptr : 0x8fa00000 , surface ptr : 0xafc00000
***************************************************
Loader:elf Filesys:raw Dev:nandflash0.kernel File: Options:bmem=192M lpj=203264 ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs rw console=ttyS0,115200
Loading: 0x80001000/6497856 0x80633640/142432 Entry address is 0x80005470
TP1 Entry Address at 0x80000ffc = 80005470
Starting program at 0x80005470
Linux version 2.6.31-3.2 (build@buildserver) (gcc version 4.4.4 (GCC) ) #1 SMP Sat Jul 23 05:14:44 CEST 2011
Fetching vars from bootloader... found 11 vars.
Early serial console at MMIO 0x10400b00 (options '115200n8')
console [uart0] enabled
Options: sata=1 enet=1 emac_1=1 no_mdio=0 docsis=0 pci=1 smp=1 moca=0 usb=1
Using 512 MB + 0 MB RAM (from CFE)
CPU revision is: 0002a044 (Brcm4380)
FPU revision is: 00130001
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
memory: 10000000 @ 20000000 (usable)
bmem: adding 192 MB RESERVED region at 64 MB (0x0c000000@0x04000000)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00030000
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000000 -> 0x00010000
0: 0x00020000 -> 0x00030000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129536
Kernel command line: bmem=192M lpj=203264 ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs rw console=ttyS0,115200
PID hash table entries: 2048 (order: 11, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
Memory: 316292k/524288k available (5032k kernel code, 207644k reserved, 1102k data, 212k init, 0k highmem)
NR_IRQS:128
Detected MIPS clock frequency: 404 MHz (202.497 MHz counter)
Console: colour dummy device 80x25
Calibrating delay loop (skipped) preset value.. 406.52 BogoMIPS (lpj=203264)
Mount-cache hash table entries: 512
SMP: Booting CPU1...
CPU revision is: 0002a044 (Brcm4380)
FPU revision is: 00130001
Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
Calibrating delay loop (skipped) preset value.. 406.52 BogoMIPS (lpj=203264)
SMP: CPU1 is running
Brought up 2 CPUs
NET: Registered protocol family 16
PCI2.3->SDRAM window: 512 MB
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42)
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
NTFS driver 2.1.29 [Flags: R/W].
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 618
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A
console handover: boot [uart0] -> real [ttyS0]
loop: module loaded
brcm-pm: enabling sata clocks
PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
scsi0 : sata_brcmstb
scsi1 : sata_brcmstb
ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42
ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42
bcmemac: Broadcom STB 10/100 EMAC driver v3.0
bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:16:b4:03:75:70)
bcmemac: not registering interface #1 at 0x10090000 (no PHY detected)
pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new interface driver pegasus
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver net1080
usbcore: registered new interface driver cdc_subset
usbcore: registered new interface driver zaurus
Broadcom STB NAND controller (BrcmNand Controller)
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
brcm-pm: enabling usb clocks
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ehci-brcm ehci-brcm.1: Broadcom STB EHCI
ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3
ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci-brcm ohci-brcm.1: Broadcom STB OHCI
ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4
ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-8: SAMSUNG HD204UI, 1AQ10001, max UDMA/133
ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD204UI 1AQ1 PQ: 0 ANSI: 5
sd 0:0:0:0: Attached scsi generic sg0 type 0
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
Bluetooth: Generic Bluetooth USB driver ver 0.5
usbcore: registered new interface driver btusb
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.20.
ALSA device list:
No soundcards found.
TCP cubic registered
sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
NET: Registered protocol family 17
Bluetooth: L2CAP ver 2.13
Bluetooth: L2CAP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
EBI CS1: setting up NAND flash (primary)
mtd->oobsize=0, mtd->eccOobSize=0
NAND_CS_NAND_XOR=00000000
B4: NandSelect=50000200, nandConfig=15142200, chipSelect=1
brcmnand_read_id: CS1: dev_id=ecf10095
After: NandSelect=50000200, nandConfig=15142200
Block size=00020000, erase shift=17
NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
timing1 not adjusted: 5363444f
timing2 not adjusted: 00000fc6
eccLevel=15, 1Ksector=0, oob=16
nbrBitsPerCell=2, cellinfo=0, chip->cellinfo=00000000
<--brcmnand_set_acccontrol: acc b4: d7ff1010, after: d7ff1010
BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB on CS1
Found NAND on CS1: ACC=d7ff1010, cfg=15142200, flashId=ecf10095, tim1=5363444f, tim2=00000fc6
BrcmNAND version = 0x0302 128MB @00000000
B4: NandSelect=50000200, nandConfig=15142200, chipSelect=1
brcmnand_read_id: CS1: dev_id=ecf10095
After: NandSelect=50000200, nandConfig=15142200
Found NAND flash on Chip Select 1, chipSize=128MB, usable size=128MB, base=0
brcmnand_scan: B4 nand_select = 50000200
brcmnand_scan: After nand_select = 50000200
usb 2-1: new high speed USB device using ehci-brcm and address 2
page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
Brcm NAND controller version = 3.2 NAND flash size 128MB @18000000
ECC layout=brcmnand_oob_bch4_4k
brcmnand_scan: mtd->oobsize=64
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
-->brcmnand_default_bbt
brcmnand_default_bbt: bbt_td = bbt_main_descr
cmdlinepart partition parsing not available
sda:
RedBoot partition parsing not available
Creating 5 MTD partitions on "brcmnand.0":
0x000000000000-0x000007f00000 : "complete"
0x000000000000-0x000000400000 : "kernel"
0x000000400000-0x000000600000 : "boot"
0x000000600000-0x000007f00000 : "rootfs"
0x000007f00000-0x000008000000 : "bbt"
UBI: attaching mtd3 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
sda1
sd 0:0:0:0: [sda] Attached SCSI disk
usb 2-1: configuration #1 chosen from 1 choice
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 4 ports detected
ata2: SATA link down (SStatus 4 SControl 300)
usb 2-1.2: new full speed USB device using ehci-brcm and address 3
usb 2-1.2: configuration #1 chosen from 1 choice
UBI: attached mtd3 to ubi0
UBI: MTD device name: "rootfs"
UBI: MTD device size: 121 MiB
UBI: number of good PEBs: 967
UBI: number of bad PEBs: 1
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 967
UBI: number of PEBs reserved for bad PEB handling: 9
UBI: max/mean erase counter: 2/0
UBI: image sequence number: 1591210834
UBI: background thread "ubi_bgt0d" started, PID 42
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size: 119738368 bytes (116932 KiB, 114 MiB, 943 LEBs)
UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 0 bytes (0 KiB)
VFS: Mounted root (ubifs filesystem) on device 0:12.
Freeing unused kernel memory: 212k freed
INIT: version 2.86 booting
Please wait: booting...
mount: mounting sysfs on /sys failed: Device or resource busy
mount: can't find /dev/sda1 in /etc/fstab
EXT4-fs (sda1): barriers enabled
kjournald2 starting: pid 83, dev sda1:8, commit interval 5 seconds
EXT4-fs (sda1): internal journal on sda1:8
EXT4-fs (sda1): delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs (sda1): recovery complete
EXT4-fs (sda1): mounted filesystem with ordered data mode
Root filesystem already rw, not remounting
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter
usbcore: registered new interface driver belkin
belkin_sa: v1.2:USB Belkin Serial converter driver
cdfs 2.6.27 loaded.
usbcore: registered new interface driver tpm
modloader: module license 'PROPRIETARY' taints kernel.
Disabling lock debugging due to kernel taint
dvb: module_layout: kernel tainted.
input: dreambox advanced remote control (native) as /class/input/input0
DVB: registering new adapter (dvb0)
DVB: registering adapter 0 frontend 0 (DVB-S2)...
DVB: registering adapter 0 frontend 1 (DVB-S2)...
input: front panel as /class/input/input1
USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
ftdi_sio: v1.5.0:USB FTDI Serial Converters Driver
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
USB Serial support registered for Keyspan - (without firmware)
USB Serial support registered for Keyspan 1 port adapter
USB Serial support registered for Keyspan 2 port adapter
USB Serial support registered for Keyspan 4 port adapter
usbcore: registered new interface driver keyspan
keyspan: v1.1.5:Keyspan USB to Serial Converter Driver
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
usbcore: registered new interface driver r871x_usb_drv
cat: can't open '/etc/videomode': No such file or directory
ALSA: Restoring mixer settings...
Configuring network interfaces... eth0 no wireless extensions.
udhcpc (v1.18.3) started
Sending discover...
Sending select for 192.168.1.127...
Lease of 192.168.1.127 obtained, lease time 3600
adding dns 192.168.1.1
done.
Starting portmap daemon: portmap.
Mounting remote filesystems...
vm.dirty_writeback_centisecs = 300
vm.dirty_background_ratio = 1
vm.dirty_ratio = 60
Downloading http://downloads.pli...ty/Packages.gz.
Inflating http://downloads.pli...ty/Packages.gz.
Updated list of available packages in /var/lib/opkg/openpli-3rd-party.
Downloading http://downloads.pli...ll/Packages.gz.
Inflating http://downloads.pli...ll/Packages.gz.
Updated list of available packages in /var/lib/opkg/openpli-all.
Downloading http://downloads.pli...00/Packages.gz.
Inflating http://downloads.pli...00/Packages.gz.
Updated list of available packages in /var/lib/opkg/openpli-et9000.
Downloading http://downloads.pli...el/Packages.gz.
Inflating http://downloads.pli...el/Packages.gz.
Updated list of available packages in /var/lib/opkg/openpli-mipsel.
Package enigma2-plugin-drivers-usbserial (1.0-r0) installed in root is up to date.
Package enigma2-plugin-extensions-autotimer (experimental-git3273+5656481-r4) installed in root is up to date.
Package enigma2-plugin-extensions-cccaminfo (svn-2940-r0-OE2.0) installed in root is up to date.
Package enigma2-plugin-extensions-dvdplayer (2.7+git8735+cb6e4a6-r26) installed in root is up to date.
Package enigma2-plugin-extensions-et9000-multiquickbutton (r2.8.0) installed in root is up to date.
Unknown package 'enigma2-plugin-extensions-et9000-pluginsort'.
Collected errors:
* opkg_install_cmd: Cannot install package enigma2-plugin-extensions-et9000-pluginsort.
Package enigma2-plugin-extensions-fritzcall (experimental-git3273+5656481-r4) installed in root is up to date.
Package enigma2-plugin-extensions-letterbox (experimental-git3273+5656481-r4) installed in root is up to date.
Installing enigma2-plugin-extensions-opkg-tools (1.2) to root...
Downloading http://downloads.pli...1.2_mipsel.ipk.
Configuring enigma2-plugin-extensions-opkg-tools.
Package enigma2-plugin-extensions-project-valerie (1.0+svnr859-r3) installed in root is up to date.
Unknown package 'enigma2-plugin-extensions-timeshiftsave'.
Collected errors:
* opkg_install_cmd: Cannot install package enigma2-plugin-extensions-timeshiftsave.
Package enigma2-plugin-extensions-weatherplugin (experimental-git3273+5656481-r4) installed in root is up to date.
Package enigma2-plugin-picons-hd-white (2011-04-22--17-36-03) installed in hdd is up to date.
Package enigma2-plugin-pli-autobackup (1.0+git72+e218e19-r2) installed in root is up to date.
Package enigma2-plugin-pli-streaminterface (1.0+git72+e218e19-r2) installed in root is up to date.
Package enigma2-plugin-skins-dmm-hd (experimental-git378+9e11f21-r1) installed in root is up to date.
Package enigma2-plugin-softcams-cccam (2.2.1-r0) installed in root is up to date.
Installing enigma2-plugin-systemplugins-blindscan (2011-04-15) to root...
Downloading http://downloads.pli...-15_mipsel.ipk.
Configuring enigma2-plugin-systemplugins-blindscan.
Restarting Enigma2 to load Blindscan ...
INIT: Switching to runlevel: 4
INIT: Sending procesStarting system message bus: dbus.
Starting Dropbear SSH server: dropbear.
Starting internet superserver: inetd.
Starting Samba: smbd nmbd.
Starting syslogd/klogd: done
* starting FTP Server: vsftpd... done.
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
...done.
INIT: no more processes left in this runlevel
CFE> printenv
Variable Name Value
-------------------- --------------------------------------------------
BOOT_CONSOLE uart0
LINUX_FFS_STARTAD 0
LINUX_FFS_SIZE 0
SPLASH_PART_STARTAD 80000
SPLASH_PART_SIZE 200000
ETH0_HWADDR 00:16:B4:03:75:70
STARTUPVERSION 1
LINUX_PART_STARTAD 0
LINUX_PART_SIZE 400000
DRAM0_SIZE 512
DRAM1_SIZE 0
FLASH_TYPE NOR
FLASH_SIZE 4
CFE_VERSION 2.12.26
CFE_BOARDNAME BCM97405B1
CFE_MEMORYSIZE 128
CFE initialized.
Set default GPIO...
USB: New device connected to bus 1 hub 1 port 1
USB: Resetting device on bus 1 port 1
USB: Locating Class 09 Vendor 1A40 Product 0101: USB Hub
USB: New device connected to bus 1 hub 2 port 2
USB: Resetting device on bus 1 port 2
USB: Locating Class 02 Vendor DEAD Product BEEF: Ethernet Device
USB: [Transfer error: 4]
USB CDC Device (00:00:00:00:00:00)
Starting splash screen.
***************************************************
Found splash image - Width = 720 Height = 576
bmp ptr : 0x8fa00000 , surface ptr : 0xafc00000
***************************************************
Loader:elf Filesys:raw Dev:nandflash0.kernel File: Options:bmem=192M lpj=203264 ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs rw console=ttyS0,115200
Loading: 0x80001000/6497856 0x80633640/142432 Entry address is 0x80005470
TP1 Entry Address at 0x80000ffc = 80005470
Starting program at 0x80005470
Linux version 2.6.31-3.2 (build@buildserver) (gcc version 4.4.4 (GCC) ) #1 SMP Sat Jul 23 05:14:44 CEST 2011
Fetching vars from bootloader... found 11 vars.
Early serial console at MMIO 0x10400b00 (options '115200n8')
console [uart0] enabled
Options: sata=1 enet=1 emac_1=1 no_mdio=0 docsis=0 pci=1 smp=1 moca=0 usb=1
Using 512 MB + 0 MB RAM (from CFE)
CPU revision is: 0002a044 (Brcm4380)
FPU revision is: 00130001
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
memory: 10000000 @ 20000000 (usable)
bmem: adding 192 MB RESERVED region at 64 MB (0x0c000000@0x04000000)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00030000
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000000 -> 0x00010000
0: 0x00020000 -> 0x00030000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129536
Kernel command line: bmem=192M lpj=203264 ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs rw console=ttyS0,115200
PID hash table entries: 2048 (order: 11, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
Memory: 316292k/524288k available (5032k kernel code, 207644k reserved, 1102k data, 212k init, 0k highmem)
NR_IRQS:128
Detected MIPS clock frequency: 404 MHz (202.497 MHz counter)
Console: colour dummy device 80x25
Calibrating delay loop (skipped) preset value.. 406.52 BogoMIPS (lpj=203264)
Mount-cache hash table entries: 512
SMP: Booting CPU1...
CPU revision is: 0002a044 (Brcm4380)
FPU revision is: 00130001
Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
Calibrating delay loop (skipped) preset value.. 406.52 BogoMIPS (lpj=203264)
SMP: CPU1 is running
Brought up 2 CPUs
NET: Registered protocol family 16
PCI2.3->SDRAM window: 512 MB
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42)
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
NET: Registered protocol family 1
NTFS driver 2.1.29 [Flags: R/W].
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 618
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A
console handover: boot [uart0] -> real [ttyS0]
loop: module loaded
brcm-pm: enabling sata clocks
PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
scsi0 : sata_brcmstb
scsi1 : sata_brcmstb
ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42
ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42
bcmemac: Broadcom STB 10/100 EMAC driver v3.0
bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:16:b4:03:75:70)
bcmemac: not registering interface #1 at 0x10090000 (no PHY detected)
pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new interface driver pegasus
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver net1080
usbcore: registered new interface driver cdc_subset
usbcore: registered new interface driver zaurus
Broadcom STB NAND controller (BrcmNand Controller)
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
brcm-pm: enabling usb clocks
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ehci-brcm ehci-brcm.1: Broadcom STB EHCI
ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3
ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci-brcm ohci-brcm.1: Broadcom STB OHCI
ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4
ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-8: SAMSUNG HD204UI, 1AQ10001, max UDMA/133
ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD204UI 1AQ1 PQ: 0 ANSI: 5
sd 0:0:0:0: Attached scsi generic sg0 type 0
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
Bluetooth: Generic Bluetooth USB driver ver 0.5
usbcore: registered new interface driver btusb
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.20.
ALSA device list:
No soundcards found.
TCP cubic registered
sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
NET: Registered protocol family 17
Bluetooth: L2CAP ver 2.13
Bluetooth: L2CAP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
EBI CS1: setting up NAND flash (primary)
mtd->oobsize=0, mtd->eccOobSize=0
NAND_CS_NAND_XOR=00000000
B4: NandSelect=50000200, nandConfig=15142200, chipSelect=1
brcmnand_read_id: CS1: dev_id=ecf10095
After: NandSelect=50000200, nandConfig=15142200
Block size=00020000, erase shift=17
NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
timing1 not adjusted: 5363444f
timing2 not adjusted: 00000fc6
eccLevel=15, 1Ksector=0, oob=16
nbrBitsPerCell=2, cellinfo=0, chip->cellinfo=00000000
<--brcmnand_set_acccontrol: acc b4: d7ff1010, after: d7ff1010
BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB on CS1
Found NAND on CS1: ACC=d7ff1010, cfg=15142200, flashId=ecf10095, tim1=5363444f, tim2=00000fc6
BrcmNAND version = 0x0302 128MB @00000000
B4: NandSelect=50000200, nandConfig=15142200, chipSelect=1
brcmnand_read_id: CS1: dev_id=ecf10095
After: NandSelect=50000200, nandConfig=15142200
Found NAND flash on Chip Select 1, chipSize=128MB, usable size=128MB, base=0
brcmnand_scan: B4 nand_select = 50000200
brcmnand_scan: After nand_select = 50000200
usb 2-1: new high speed USB device using ehci-brcm and address 2
page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
Brcm NAND controller version = 3.2 NAND flash size 128MB @18000000
ECC layout=brcmnand_oob_bch4_4k
brcmnand_scan: mtd->oobsize=64
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
-->brcmnand_default_bbt
brcmnand_default_bbt: bbt_td = bbt_main_descr
cmdlinepart partition parsing not available
sda:
RedBoot partition parsing not available
Creating 5 MTD partitions on "brcmnand.0":
0x000000000000-0x000007f00000 : "complete"
0x000000000000-0x000000400000 : "kernel"
0x000000400000-0x000000600000 : "boot"
0x000000600000-0x000007f00000 : "rootfs"
0x000007f00000-0x000008000000 : "bbt"
UBI: attaching mtd3 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
sda1
sd 0:0:0:0: [sda] Attached SCSI disk
usb 2-1: configuration #1 chosen from 1 choice
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 4 ports detected
ata2: SATA link down (SStatus 4 SControl 300)
usb 2-1.2: new full speed USB device using ehci-brcm and address 3
usb 2-1.2: configuration #1 chosen from 1 choice
UBI: attached mtd3 to ubi0
UBI: MTD device name: "rootfs"
UBI: MTD device size: 121 MiB
UBI: number of good PEBs: 967
UBI: number of bad PEBs: 1
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 967
UBI: number of PEBs reserved for bad PEB handling: 9
UBI: max/mean erase counter: 2/0
UBI: image sequence number: 1591210834
UBI: background thread "ubi_bgt0d" started, PID 42
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size: 119738368 bytes (116932 KiB, 114 MiB, 943 LEBs)
UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 0 bytes (0 KiB)
VFS: Mounted root (ubifs filesystem) on device 0:12.
Freeing unused kernel memory: 212k freed
INIT: version 2.86 booting
Please wait: booting...
mount: mounting sysfs on /sys failed: Device or resource busy
mount: can't find /dev/sda1 in /etc/fstab
EXT4-fs (sda1): barriers enabled
kjournald2 starting: pid 83, dev sda1:8, commit interval 5 seconds
EXT4-fs (sda1): internal journal on sda1:8
EXT4-fs (sda1): delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs (sda1): recovery complete
EXT4-fs (sda1): mounted filesystem with ordered data mode
Root filesystem already rw, not remounting
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter
usbcore: registered new interface driver belkin
belkin_sa: v1.2:USB Belkin Serial converter driver
cdfs 2.6.27 loaded.
usbcore: registered new interface driver tpm
modloader: module license 'PROPRIETARY' taints kernel.
Disabling lock debugging due to kernel taint
dvb: module_layout: kernel tainted.
input: dreambox advanced remote control (native) as /class/input/input0
DVB: registering new adapter (dvb0)
DVB: registering adapter 0 frontend 0 (DVB-S2)...
DVB: registering adapter 0 frontend 1 (DVB-S2)...
input: front panel as /class/input/input1
USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
ftdi_sio: v1.5.0:USB FTDI Serial Converters Driver
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
USB Serial support registered for Keyspan - (without firmware)
USB Serial support registered for Keyspan 1 port adapter
USB Serial support registered for Keyspan 2 port adapter
USB Serial support registered for Keyspan 4 port adapter
usbcore: registered new interface driver keyspan
keyspan: v1.1.5:Keyspan USB to Serial Converter Driver
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
usbcore: registered new interface driver r871x_usb_drv
cat: can't open '/etc/videomode': No such file or directory
ALSA: Restoring mixer settings...
Configuring network interfaces... eth0 no wireless extensions.
udhcpc (v1.18.3) started
Sending discover...
Sending select for 192.168.1.127...
Lease of 192.168.1.127 obtained, lease time 3600
adding dns 192.168.1.1
done.
Starting portmap daemon: portmap.
Mounting remote filesystems...
vm.dirty_writeback_centisecs = 300
vm.dirty_background_ratio = 1
vm.dirty_ratio = 60
Downloading http://downloads.pli...ty/Packages.gz.
Inflating http://downloads.pli...ty/Packages.gz.
Updated list of available packages in /var/lib/opkg/openpli-3rd-party.
Downloading http://downloads.pli...ll/Packages.gz.
Inflating http://downloads.pli...ll/Packages.gz.
Updated list of available packages in /var/lib/opkg/openpli-all.
Downloading http://downloads.pli...00/Packages.gz.
Inflating http://downloads.pli...00/Packages.gz.
Updated list of available packages in /var/lib/opkg/openpli-et9000.
Downloading http://downloads.pli...el/Packages.gz.
Inflating http://downloads.pli...el/Packages.gz.
Updated list of available packages in /var/lib/opkg/openpli-mipsel.
Package enigma2-plugin-drivers-usbserial (1.0-r0) installed in root is up to date.
Package enigma2-plugin-extensions-autotimer (experimental-git3273+5656481-r4) installed in root is up to date.
Package enigma2-plugin-extensions-cccaminfo (svn-2940-r0-OE2.0) installed in root is up to date.
Package enigma2-plugin-extensions-dvdplayer (2.7+git8735+cb6e4a6-r26) installed in root is up to date.
Package enigma2-plugin-extensions-et9000-multiquickbutton (r2.8.0) installed in root is up to date.
Unknown package 'enigma2-plugin-extensions-et9000-pluginsort'.
Collected errors:
* opkg_install_cmd: Cannot install package enigma2-plugin-extensions-et9000-pluginsort.
Package enigma2-plugin-extensions-fritzcall (experimental-git3273+5656481-r4) installed in root is up to date.
Package enigma2-plugin-extensions-letterbox (experimental-git3273+5656481-r4) installed in root is up to date.
Installing enigma2-plugin-extensions-opkg-tools (1.2) to root...
Downloading http://downloads.pli...1.2_mipsel.ipk.
Configuring enigma2-plugin-extensions-opkg-tools.
Package enigma2-plugin-extensions-project-valerie (1.0+svnr859-r3) installed in root is up to date.
Unknown package 'enigma2-plugin-extensions-timeshiftsave'.
Collected errors:
* opkg_install_cmd: Cannot install package enigma2-plugin-extensions-timeshiftsave.
Package enigma2-plugin-extensions-weatherplugin (experimental-git3273+5656481-r4) installed in root is up to date.
Package enigma2-plugin-picons-hd-white (2011-04-22--17-36-03) installed in hdd is up to date.
Package enigma2-plugin-pli-autobackup (1.0+git72+e218e19-r2) installed in root is up to date.
Package enigma2-plugin-pli-streaminterface (1.0+git72+e218e19-r2) installed in root is up to date.
Package enigma2-plugin-skins-dmm-hd (experimental-git378+9e11f21-r1) installed in root is up to date.
Package enigma2-plugin-softcams-cccam (2.2.1-r0) installed in root is up to date.
Installing enigma2-plugin-systemplugins-blindscan (2011-04-15) to root...
Downloading http://downloads.pli...-15_mipsel.ipk.
Configuring enigma2-plugin-systemplugins-blindscan.
Restarting Enigma2 to load Blindscan ...
INIT: Switching to runlevel: 4
INIT: Sending procesStarting system message bus: dbus.
Starting Dropbear SSH server: dropbear.
Starting internet superserver: inetd.
Starting Samba: smbd nmbd.
Starting syslogd/klogd: done
* starting FTP Server: vsftpd... done.
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
...done.
INIT: no more processes left in this runlevel
CFE> printenv
Variable Name Value
-------------------- --------------------------------------------------
BOOT_CONSOLE uart0
LINUX_FFS_STARTAD 0
LINUX_FFS_SIZE 0
SPLASH_PART_STARTAD 80000
SPLASH_PART_SIZE 200000
ETH0_HWADDR 00:16:B4:03:75:70
STARTUPVERSION 1
LINUX_PART_STARTAD 0
LINUX_PART_SIZE 400000
DRAM0_SIZE 512
DRAM1_SIZE 0
FLASH_TYPE NOR
FLASH_SIZE 4
CFE_VERSION 2.12.26
CFE_BOARDNAME BCM97405B1
CFE_MEMORYSIZE 128
Re: Can´t flash OpenPli 2.1 #10
-
- PLi® Core member
- 32,766 posts
+245
Excellent
Posted 24 July 2011 - 20:44
enigma2-plugin-systemplugins-blindscan for some reason is switching your box to runlevel 4.
So the image boots fine, but you end up without a running enigma2, because of whatever this plugin is trying to do during its install
To make it work, remove the enigma2-plugin-systemplugins-blindscan line from /media/hdd/autoinstall.
But I'm quite sure you can fix the problem without having to reinstall the image, by switching the box back to runlevel 3, and/or restarting.
Bottom line is, enigma2-plugin-systemplugins-blindscan performs some dirty tricks, which apparently do not work when it is installed from the autoinstall file, during the initial boot.
So the image boots fine, but you end up without a running enigma2, because of whatever this plugin is trying to do during its install
To make it work, remove the enigma2-plugin-systemplugins-blindscan line from /media/hdd/autoinstall.
But I'm quite sure you can fix the problem without having to reinstall the image, by switching the box back to runlevel 3, and/or restarting.
Bottom line is, enigma2-plugin-systemplugins-blindscan performs some dirty tricks, which apparently do not work when it is installed from the autoinstall file, during the initial boot.
Re: Can´t flash OpenPli 2.1 #11
-
- PLi® Core member
- 10,036 posts
+339
Excellent
Posted 25 July 2011 - 05:14
enigma2-plugin-extensions-et9000-pluginsort
this plugin does not disable or do restart, all the time green screen.
this plugin does not disable or do restart, all the time green screen.
Re: Can´t flash OpenPli 2.1 #12
-
- PLi® Core member
- 14,045 posts
+298
Excellent
Posted 25 July 2011 - 06:57
From what it writes to the log file:
Configuring enigma2-plugin-systemplugins-blindscan.
Restarting Enigma2 to load Blindscan ...
It apparently kills enigma2 as a post-install action... Nice move.
Configuring enigma2-plugin-systemplugins-blindscan.
Restarting Enigma2 to load Blindscan ...
It apparently kills enigma2 as a post-install action... Nice move.
Real musicians never die - they just decompose
Re: Can´t flash OpenPli 2.1 #13
-
- Senior Member
- 52 posts
0
Neutral
Posted 25 July 2011 - 09:22
OK,
I try to remove Blindscan from hdd with openpli 2.0 reflash with openpli2.1
good to know that installed plugins from a previous version to be updatet by startupscript from openpli2.1
is that the right way, i try this after my work....
thx for support
Frank
I try to remove Blindscan from hdd with openpli 2.0 reflash with openpli2.1
good to know that installed plugins from a previous version to be updatet by startupscript from openpli2.1
is that the right way, i try this after my work....
thx for support
Frank
Re: Can´t flash OpenPli 2.1 #14
-
- Senior Member
- 52 posts
0
Neutral
Posted 26 July 2011 - 08:52
ok guys,
it´s working now ... after move autoinstall in /media/hdd/backup everything works fine!
thx for support and keep up your good job
br
frank
it´s working now ... after move autoinstall in /media/hdd/backup everything works fine!
thx for support and keep up your good job
br
frank
Also tagged with one or more of these keywords: ET9000
OpenPLI auf et9000 mit crashlog bei rebootStarted by manyone, 8 Dec 2019  et9000
|
|
|
||
ET9000 with SSD crashesStarted by erwin288, 26 Jan 2019 ET9000, SSD, Xtrend, crash
|
|
|
||
Sundtek USB Kabel tuner ET9000Started by KBDE, 23 Jan 2019 sundtek, cablescan, ET9000
|
|
|
||
Geluid stopt bij afspelen MKV ET9000Started by jbnl, 24 Nov 2018 mkv, et9000, geluid
|
|
|
||
Xbox One USB tuner op de ET9000Started by jbnl, 4 Sep 2017 usb, xtrend, et9000, tuner
|
|
|
1 user(s) are reading this topic
0 members, 1 guests, 0 anonymous users
