Hi,
I just perform an opkg update && opkg upgrade and my box turns into an infinite booting loop(boot - OpenPLi logo - spinner - reboot -> boot,...)
Can anyone confirm this problem?
Pr2
today update infinite loop on Xtrend ET-9000?
Started by Pr2, 28 Jul 2014 10:46
4 replies to this topic
#1
-
- PLi® Contributor
- 6,075 posts
+257
Excellent
Posted 28 July 2014 - 10:46
NO SUPPORT by PM, it is a forum make your question public so everybody can benefit from the question/answer.
If you think that my answer helps you, you can press the up arrow in bottom right of the answer.
Wanna help with OpenPLi Translation? Please read our Wiki Information for translators
Sat: Hotbird 13.0E, Astra 19.2E, Eutelsat5A 5.0W
VU+ Solo 4K: 2*DVB-S2 + 2*DVB-C/T/T2 (used in DVB-C) & Duo 4K: 2*DVB-S2X + DVB-C (FBC)
AB-Com: PULSe 4K 1*DVB-S2X (+ DVB-C/T/T2)
Edision OS Mio 4K: 1*DVB-S2X + 1*DVB-C/T/T2
Re: today update infinite loop on Xtrend ET-9000? #2
-
- PLi® Contributor
- 6,075 posts
+257
Excellent
Posted 28 July 2014 - 11:01
Hi,
Sounds more like an hardware failure... power it on power button blink 3 times and the nothing more.
I cannot reflash a new image...
Pr2
Sounds more like an hardware failure... power it on power button blink 3 times and the nothing more.
I cannot reflash a new image...
Pr2
NO SUPPORT by PM, it is a forum make your question public so everybody can benefit from the question/answer.
If you think that my answer helps you, you can press the up arrow in bottom right of the answer.
Wanna help with OpenPLi Translation? Please read our Wiki Information for translators
Sat: Hotbird 13.0E, Astra 19.2E, Eutelsat5A 5.0W
VU+ Solo 4K: 2*DVB-S2 + 2*DVB-C/T/T2 (used in DVB-C) & Duo 4K: 2*DVB-S2X + DVB-C (FBC)
AB-Com: PULSe 4K 1*DVB-S2X (+ DVB-C/T/T2)
Edision OS Mio 4K: 1*DVB-S2X + 1*DVB-C/T/T2
Re: today update infinite loop on Xtrend ET-9000? #3
-
- PLi® Core member
- 7,185 posts
+323
Excellent
Posted 28 July 2014 - 13:34
Blinking led means in almost all cases a problem with the power supply. Check electrolytic capacitor of power supply unit. Most likely one is not working any longer.
P.S Here is a thread in German regarding this
http://www.et-view-s...ll=1#post150729
P.S Here is a thread in German regarding this
http://www.et-view-s...ll=1#post150729
Edited by betacentauri, 28 July 2014 - 13:39.
Xtrend ET-9200, ET-8000, ET-10000, OpenPliPC on Ubuntu 12.04
Re: today update infinite loop on Xtrend ET-9000? #4
-
- PLi® Contributor
- 6,075 posts
+257
Excellent
Posted 28 July 2014 - 18:21
Thanks for the link I will have a look at it.
NO SUPPORT by PM, it is a forum make your question public so everybody can benefit from the question/answer.
If you think that my answer helps you, you can press the up arrow in bottom right of the answer.
Wanna help with OpenPLi Translation? Please read our Wiki Information for translators
Sat: Hotbird 13.0E, Astra 19.2E, Eutelsat5A 5.0W
VU+ Solo 4K: 2*DVB-S2 + 2*DVB-C/T/T2 (used in DVB-C) & Duo 4K: 2*DVB-S2X + DVB-C (FBC)
AB-Com: PULSe 4K 1*DVB-S2X (+ DVB-C/T/T2)
Edision OS Mio 4K: 1*DVB-S2X + 1*DVB-C/T/T2
Re: today update infinite loop on Xtrend ET-9000? #5
-
- Member
- 3 posts
0
Neutral
Posted 1 August 2014 - 20:01
I've just had the same problem, I went to the link and figured out that I had to change a capacitor on the power supply unit. ( 4700µF 105° 10V ) I did it and now it's working again.
This is the link where I went:- http://www.et-view-s...nszeichen/page3
I am worried about the temperature it's running at though, you can just about bear the heat when you touch it with a finger.
1 user(s) are reading this topic
0 members, 1 guests, 0 anonymous users
